Product specifications

• Type: DC latch
• Waterproof: IP64 certified
• Operating pressure: 10 to 100 PSI (.7 to 6.8 bar)
• Flow range: .1 to 8 GPM (.38 to 30 L/H)
• Temperature range: 38-130°F (3-54°C)
• Connection: female hose thread inlet (FHT) x male hose thread outlet (MHT) or British standard thread for tap (BSP)
• Power source: ambient light (solar)
• Sensor connection: yellow wire for closed contact rain sensor
• Power source: Ambient light (PVM)
• Input: 3,000 - 100,000+ LUX
• Sensor connection: yellow wire for closed contact sensor
• Controller dimensions: 5.75” W x 6.76” H x 2.25” D (14.6 cm W x 17.1 cm H x 6.3 cm D)
• Unit Weight including plastic clam shell packaging: 1.02 pounds (.47 kg)
• UPC code: 840620100038
• Materials:
  • Timer housing: high impact plastic
  • Inlet valve and solenoid: glass reinforced nylon with stainless steel plunger and spring

Programming options

• Watering duration: one minute up to five hours and 59 minutes set in one minute increments
• Watering frequency: weekly or cyclical schedule with odd days, even days, or intervals from one to thirty (1- 30) days utilizing 365 day yearly calendar with leap year.
  • In the weekly schedule, the hose end timer (tap timer) can be programmed to operate on any day of the week, such as Monday, Wednesday, and Friday.
    
  • In the cyclical schedule, the hose end timer can be programmed to operate on odd days, even days, or at specific intervals such as every three days.
• Up to four start times per day in weekly or cyclical schedule provides added flexibility for any type of watering application.
• Rain off/delay option with automatic restart up to 99 days
• Program off option stops program until reactivated
• Manual cycle via the program with automatic shutoff option

About

The EVO 100 is a single zone hose end electronic irrigation timer that is easy to install and program. The patented energy management system derives power only from ambient light which is collected by a small built in photovoltaic module. This energy is then stored in long-life super capacitors. There are no batteries to install or replace, and no external power supply is required. The timer has a quick-release swivel female hose thread inlet fitting and a male hose thread outlet (BSP is also available with model EVO100I).

Before you start programming, the timer will need to be charged for one to two hours in sunlight to get up to full power. Once it’s full though, as long as it gets around 10 minutes of ambient light per day, it will stay at full charge.

The timer has seven buttons with the four arrow buttons (left, right, up, and down arrows) used to select a program parameter and a large circular button to modify and accept the parameter changes. The two buttons on the right side are used for manual operation, and for program off or irrigation suspension.

The EVO 100 is a light-powered maintenance-free timer with no batteries to replace or charge.
1. Install the timer to the faucet by turning the female inlet fitting clockwise until hand tight. The female inlet has a screen washer so, do not use any wrench to tight the unit . For BSP thread models wrap TEFLON tape on each of the male thread fittings used.
2. Turn the water supply on. The timer will open momentarily and then will shut off. Note: If it does not, push the manual operation button twice to ensure that the timer is closed.
3. If the timer is installed with a drip irrigation system, make sure to install a 150 mesh or higher screen filter to protect the drip system, then add a 15, 25, or 30 PSI (1, 1.75, or 2.1 bar) pressure regulator, followed with a swivel adapter to the drip tubing.
4. Test the timer using the manual operation button located below the display. Press the button to open and start water flow. If connected to a sprinkler or drip system, check that the system is working to your satisfaction and that there are no leaks. Press the button again to turn off the unit.
5. Program the timer.
Review the instruction manual included with the unit for details.

If a rain sensor or other closed contact sensor is used, cut the yellow wires and add the sensor per the manual, sensor instructions, making sure to use a waterproof wire connection.

---

Please let us know if these instructions were helpful to you by liking it or providing feedback below.