1/4" Barbed Fittings

DIG’s 1/4” Barbed Drip Fittings are used in the installation of all brands of 1/4” micro tubing, 1/4" drip line and 1/4" soaker hose (.140 ID to .170 ID). The fittings are pushed into the inside of the tubing for a very tight-fit connection. They can be used for a two-way layout or for a three-way layout of the different tubing. The fittings can also be used to attach the micro tubing to 1/2” or 3/4” drip tubing. They are made of high-impact plastic and have the largest inside diameter in the industry with a higher flow rate capability and lower head loss.

Features

  • Sharp-barb design for secure and tight-fit installation without glue or clamps
  • Fits all brands of 1/4” micro tubing , 1/4" drip line and 1/4" soaker hose with .140 ID to .170 ID
  • One-piece construction
  • Made of high-impact, high-strength, UV-resistant plastic for durability and long life
  • Large inside diameter for maximum flow

technical


1/4" Barbed Fittings
how to order
Model Description Image
D5010 Self piercing 1/4 in. Insert Connector , (pack of 5) D5010
H84B 1/4 in. Barbed Elbow, (PACK OF 10)
Aids in turning 1/4" micro tubing around sharp corners
H84B
1/4 in. Barbed Coupling
H80A 1/4 in. barbed connector, (pack of 10) H80A
H80B 1/4 in. barbed connector, (pack of 50)
1/4 in. Barbed Tee
H82A 1/4 in. Barbed Tee, (pack of 10) H82A
H82B 1/4 in. Barbed Tee, (pack of 50)

Products specifications

  • Operating pressure: up to 30 PSI
  • Color: black
  • Use with 1/4” micro tubing, 1/4" drip line and 1/4" soaker hose (.140 ID to .170 ID)
  • Material: Acetal



how to use


1/4" Barbed Fittings

About

DIG’s 1/4” Barbed Drip Fittings are available in a range of configurations for use with 1/4” micro tubing (also known as distribution tubing), 1/4" drip line and 1/4" soaker hose. They provide a low cost and simple method for the installation of the different tubing. The main purpose of the fittings is to allow the extension of drip emitters or 1/4” drip line from the drip tubing into the plant areas. They use a sharp barb over which the end of the tubing is pushed for a very tight fit.

Barbed fittings Installation

To connect the barbed fittings, force the tubing over the barb of the connector, tee or elbow. To connect 1/4” micro tubing into the 1/2” drip tubing, punch a hole into the 1/2” drip tubing, snap the barbed fitting into the hole and push the micro tubing over the other side of the barb. The 1/4" fittings are available in a barbed connector, tee or elbow to meet the varying requirements in the installation and layout of the micro tubing and 1/4" drip line.


Please let us know if these instructions were helpful to you by liking it or providing feedback below.




DIG_logo_white_web
Homeowner Resources

Manuals
Videos & Articles
Catalogs

Irrigation-Association-logo American-Society-of-irrigation-consultants-Logo American-Society-of-Landscape-Architects-Logo Recycling-logo

DIG Corporation
1210 Activity Drive
Vista, CA 92081 USA

Tel: (760) 727-0914
Fax: (760) 727-0282
Toll Free: (800) 322-9146


© copyright 2019 DIG Corporation water matters™ | All rights reserved | Privacy Policy | Terms of Use