8006 Six-Station AC Timer with Independent Programming for Each Valve

The Six-Station 24 VAC indoor mounting timer features independent programming for each valve, allowing maximum flexibility for any type of irrigation system and any zone requirements. The 8006 AC timer includes a 120/24 transformer, is simple to install and program, and offers versatile scheduling for sprinkler or drip systems. Designed for residential and light commercial applications, the six station indoor AC controller uses special programming features that allow each valve to be programmed independently from the others so that each zone can have independent schedules, start times, and watering durations. The controller features an easy-to-read LCD display with AM/PM clock and independent programs for each valve with four start times per day, durations from 1 minute to 12 hours in 1-minute increments, weekly calendar or intervals from 1 to 30 days. The controller also includes a rain delay feature that allows delay of a program up to 30 days, and a sensor terminal for rain stop.

Features

  • Independent program for each valve
  • Operates six valves and master valve (or pump)
  • Can operate two valves simultaneously
  • Four buttons with an integrated LCD display
  • see more
  • Easy to read AM/PM clock
  • Operates with 24 VAC valves
  • Independent programming of start time, run time and day of the week for each valve
  • Automatic, semi-automatic and manual operation
  • Weekly or cyclical program
  • Up to four start times per day, per valve, in weekly mode
  • Sequential “manual” operation of all the valves via the irrigation controller
  • Irrigation duration variable according to percentage value
  • Identifies short circuits, isolates the faulty valve and continues the irrigation cycle with visible alarm
  • If power is disrupted, a blinking display indicates that there is no power
  • Operates off 120 VAC transformer
  • 9-volt alkaline battery backup to retain program memory during a power outage (battery not included)
  • Three year manufacturer’s warranty

technical


how to order
Model Description
8006 Six Station AC Timer

Product specifications

  • Input required: 110 VAC, 60 Hz 28 VA input (UL listed plug in transformer)
  • Station output: 24 VAC, 0.27 amps per station
  • Maximum output: 24 VAC, 0.83 mA
  • Program backup: 9-volt battery
  • Dimensions: 6” (15 cm) height x 4” (10 cm) width x 2” (5 cm) depth

Programming features

  • Watering duration: 1 minute to 11 hours and 59 minutes, in 1 minute increments
  • Watering schedule: cyclical or weekly mode
  • Cyclical schedules from once every 3, 6, 12, 24 hours and up to 30 days
  • Weekly mode on any days of the week such as Monday, Wednesday and Friday
  • Four start times per day in a weekly mode
  • Budget with increments from 10% up to 90% in 10% increments
  • "Rain Off" mode
  • Rain delay up to 30 days with auto restart
Box Contents
qty description
1 Six station controller
1 transformer: 120VAC,60Hz
1 Instruction manual

|1 | 50' 1/4" micro tubing |




manuals


Manuals

  • Thumb_8006_inst_web_040711
    English
    05/07/2013

    8004, 8006 AC controller ( after 2002 )

  • Thumb_8004-8006-b402
    English
    05/07/2013

    8004, 8006 AC controller ( before 2002 )


how to use


About

An irrigation controller should be selected with care, especially if the irrigation system is operating a combination of sprinkler and drip zones. If your irrigation system is currently manually operated, consider the benefits of automating, including convenience and reduced labor, watering a number of valves automatically with full landscape coverage, and the ability to control the days, durations, and irrigation start times for each valve. Automation also allows the installation of a rain sensor to stop irrigation when it is rainy. It is important to review and adjust your irrigation program schedules frequently to avoid over-or under-watering when there is a change in weather pattern. The 8006 controller offers automated programming flexibility for drip irrigation or sprinkler systems by allowing each of the zones/valve to be programmed independently, according to plant water requirements. The 8006 controller permits each valve in the system to operate independent of the others, offering durations from 1 minute to 11 hours and 59 minutes in one minute increments, up to four start times, and independent operation for any day of the week for each valve.

Installation

  1. Select an indoor location near a 120 VAC outlet. The location should be protected from moisture and sunlight.
  2. Remove the mounting bracket from the back of the controller and place the mounting bracket slightly below eye level.
  3. Secure the bracket with #5 or 6 x 1” screws (if installing into drywall, install screw anchors).
  4. After bracket installation, place the controller down into position on the bracket.
  5. Install control wires from the controller to valve location(s). We recommended using 18-gauge multi-strand color-coded direct burial irrigation control wire.
  6. Splice one of each valve’s solenoid wires to the white (common) wire by using waterproof wire connectors.
  7. Splice the remaining of each valve’s solenoid wires to a separate color-coded control wire by using waterproof wire connectors.
  8. Remove the lower faceplate from the controller to access the controller terminal strip compartment.
  9. Cut the control wires to length and strip the ends back about 1/4 in. Secure the white (common) wire to the terminal marked C by inserting the wire into the slot and tightening the screw with a small standard screwdriver.
  10. Secure the color-coded station wires to the numbered terminals by inserting the wire into the numbered slot and tightening the screw with a small standard screwdriver.
  11. Insert the two transformer wires into the terminals labeled AC (polarity does not matter), and secure by tightening the terminal screws with a small standard screwdriver.
  12. Insert 9-volt battery.
  13. Program the controller.
  14. If connecting a master valve or PumP start relay, please consult a qualified electrician. Make sure to mount the controller 10 to 15 feet away from the pump start relay and the pump.
  15. An interrupt type, normally open rain sensor can be connected to the controller. The sensor can be connected directly to the controller sensor terminals by connecting either wire from the sensor to the two sensor terminals on the controller. Follow the sensor manufacturer’s instructions for calibrating the sensor. Note: Do not plug AC transformer into the power source before connecting the transformer to the controller. Note: Do not plug in the transformer until the controller is mounted and all valves have been connected.

Please let us know if these instructions were helpful to you by liking it or providing feedback below.




DIG-Logo-Tag
Homeowner Resources

Manuals
Videos & Articles
Catalogs

Irrigation-Association-logo American-Society-of-irrigation-consultants-Logo American-Society-of-Landscape-Architects-Logo Recycling-logo

DIG Corporation
1210 Activity Drive
Vista, CA 92081 USA

Tel: (760) 727-0914
Fax: (760) 727-0282
Toll Free: (800) 322-9146


© copyright 2013 DIG Corporation water matters™ | All rights reserved