1/4" in. Porous Soaker Hose

The PSH50 Porous Soaker Hose is an extruded small-diameter flexible pipe made of UV-resistant recycled rubber from old tires. When looked at under a magnifying glass the extruded porous soaker hose is peppered with many tiny holes, and when under pressure, sweats or weeps along the full length of the soaker hose. The porous soaker hose can be used in short lengths to water planter boxes, looped or circled around trees, or used for narrow plantings and vegetable gardens. The porous soaker hose can be connected into the drip tubing or micro tubing using 1/4" barbed fittings.

Features

  • Use for planter boxes, closely planted or narrow areas, vegetable gardens, or looped around trees.
  • Allows water to gently trickle directly to the root zone, delivering a constant deep watering through its porous openings.
  • No special tools or glue are needed.
  • Saves money by significantly lowering the cost of system components compared to conventional irrigation systems.
  • DIG's drip irrigation products may be exempt from residential and commercial watering restrictions (check local codes).

technical


1/4" in. Porous Soaker Hose
how to order
Model Description
PSH50 50 ft. Porous Soaker Hose

Product specifications

  • Operating pressure range: 10 to 25 PSI
    • Recommended operating pressure: 15 or 25 PSI (use with model D46, 25 PSI pressure regulator)
  • Flow rate per 50': 46.5 GPH @ 15 PSI and 65.3 GPH @ 25 PSI
  • Porous soaker hose length: 50' x 1/4" with .160 ID x .320 OD
  • Maximum recommended distance for a length of 1/4" soaker hose line: 15'
  • Total flow rate for this coil: 65.3 GPH (1.09 GPM) @ 25 PSI
Reommended length at operating preassure of 25 PSI
length in feet pressure loss per 50' in PSI
10' 2.8 PSI
15' 10.5 PSI
20' 20 PSI*

*Not recommended




how to use


1/4" in. Porous Soaker Hose

About

Soaker hose, like drip irrigation, delivers a constant deep watering directly over the plant roots. Water flow through the porous openings of the hose guarantees efficient watering over the length of the line used. The 1/4" soaker hose is easy to handle and well suited to water planter boxes, garden beds and plants in close spacing such as rows of shrubs.
The recycled rubber porous soaker hose can be installed above the ground and covered with mulch to blend with the landscape. For the best result, this 50' soaker hose can be cut to short lengths of up to 15' and connected into 1/2" drip tubing or 1/4" micro tubing using the 1/4" barbed fittings. The soaker hose can be used as part of a drip irrigation installation or a system with soaker hose only and operates under a range of pressures not to exceed 25 PSI. The 25 PSI or lower pressure regulator is used to lower the incoming pressure of the system to the suggested operating pressure, which is within the range of recommended pressures for a soaker hose, drip irrigation or micro sprinkler systems.

Installation suggestions:

Basic installation recommendations for this product include first reviewing the area and then making a drawing of the garden or site with your preferred layout.
If automation is required, use one of our DIG hose end timers or battery operated controllers. The ideal controller should have flexible scheduling and two to four start times per day for added flexibility.

  1. In the installation stage, to the faucet, first connect a backflow device (model D45), then a 25 PSI pressure regulator (model D46). If using 1/2" drip tubing as the supply line then add a 3/4" swivel adapter with screen (model C34). If water quality is a concern, we highly recommending using our fine mesh 3/4" filter with 155-mesh (model D57A) If the system is used from a rain barrel the pressure regulator is not needed.
  2. Lay out 1/2" drip tubing per your drawing and secure the drip tubing to the ground using stakes (model R60).
  3. Throughout the installation add fittings if needed such as tees (model C35) and elbows (model C36) leaving the end of the drip tubing open. A. Use the 1/2" drip tubing as the main lateral and connect the 1/4" porous soaker hose to the 1/2" drip tubing or to the 1/2" drip tubing connect 1/4" micro tubing and to the end of the 1/4" micro tubing connect the porous soaker hose.
  4. Connect the soaker hose into the 1/2" drip tubing by punching a hole into the 1/2" drip tubing using a punch (model D44) and inserting a 1/4" barb (model H80A or H80B) or barbed tee (model H82A or H82B). Connect the porous soaker hose into the barb fittings.
  5. If using 1/4" micro tubing, insert a 1/4" barb into the micro tubing and connect the soaker hose into the micro tubing. Keep the soaker hose to length of up to 15 feet.
  6. Lay the soaker hose along the row or loop the soaker hose around trees, roses or shrubs and secure it to the ground using a gallivanted wire (model P32B) or plastic wire (model P31B).
  7. Turn the water on and flush the line and then turn the water off.
  8. Close the end of the1/2" drip tubing using the hose end (model Q58) or figure "8" (model F68B) and then close the end of the 1/4" soaker hose using the large size of our 1/4" goof plug (model G79B). Keep the length of the soaker hose to a short run for even uniformity. It is recommended not to exceed a length of 15'.
  9. Pressure-test the system to identify leaks in the drip hose laterals, fittings and soaker hose and then program the timer or controller.

Disadvantages of soaker hose

  • Soaker hose sweats or weeps small amounts of water along its full length or along the line, so plants and weeds both are watered.
  • The soaker hose can be susceptible to damage from rodents and household pets.
  • A filter is required to guard against potential clogging of the small pores.
  • Over time, soaker hose may stiffen with age, becoming brittle and less flexible.
  • You cannot see a soaker hose system working, as opposed to a conventional sprinkler system.

About the soil and suggested watering intervals:

  • Sandy soil or light textured soil: Water percolates straight through before it can spread far enough horizontally, so apply water at close intervals such as every other day for 20 to 90 minutes depending on plant size and type, daylight conditions (full sun, partial sun or shaded) and weather pattern (cold to hot) with the plants under full sun in hot conditions getting the longer period. Loamy soil or medium textured soil: This is the ideal soil condition with water moving slowly and spreading evenly, so apply water at wider intervals such as every two to four days for 15 to 90 minutes depending on plant size, type, daylight conditions (full sun, partial sun or shaded) and weather pattern (cold to hot) with the plants under full sun in hot conditions getting the longer period. Clay soil or heavy textured soil: Water is absorbed very slowly, so apply water at longer intervals such as every three to five days for 30 to 60 minutes depending on flow rate, plant size and type, daylight conditions (full sun, partial sun or shaded) and weather pattern (cold to hot) with the plants under full sun in hot condition getting the longer period.

Please let us know if these instructions were helpful to you by liking it or providing feedback below.




DIG-Logo-Tag
Homeowner Resources

Manuals
Videos & Articles
Catalogs

Irrigation-Association-logo American-Society-of-irrigation-consultants-Logo American-Society-of-Landscape-Architects-Logo Recycling-logo

DIG Corporation
1210 Activity Drive
Vista, CA 92081 USA

Tel: (760) 727-0914
Fax: (760) 727-0282
Toll Free: (800) 322-9146


© copyright 2013 DIG Corporation water matters™ | All rights reserved